Plot No-C1-1031-9, GIDC Estate, Panoli, Ankleshwar, Gujarat - 393002. India Telephone Mobile: 91-7506449333; e-mail: info@crystalclearproducts.org

Aluminum Chloride Hexahydrate ---- Aluminium Potassium Sulphate ---- Aluminum Chlorohydrate ---- Aluminium Glycinate ---- Aluminium Magnesium Silicate ---- Dried Aluminium Phosphate ---- Dihydroxyaluminum Aminoacetate ---- Dihydroxyaluminum Sodium Carbonate ---- Aluminum Gluconate ---- Aluminum Monostearate & Aluminum Distearate ---- Aluminium Isopropoxide ---- Copper Cupric Chloride ---- Copper Sulfate ---- Ferric Ammonium Citrate ---- Ferric Chloride Hexahydrate ---- Ferric Nitrate Nonahydrate ---- Ferric Oxide ---- Ferric Sulfate ---- Ferrous Fumarate ---- Ferrous Gluconate ---- Ferrous Sulfate ---- Iron Aspartate ---- Iron Sulphide ---- Iron D Saccharate and Iron Sucrose Manufacturer & Exporter

Aluminium Magnesium Silicate or Magnesium Aluminum Silicate Specifications of Commercial Pure & BP Ph Eur USP NF Grade Manufacturers & Exporters Please check Aluminium Magnesium Silicate or Magnesium Aluminum Silicate USP NF ACS BP Ph Eur EP JP IP Analytical reagent FCC Food grade Manufacturers our associates world class FDA-GMP approved, ISO-9001 Certified facility Anmol Chemicals Aluminium Magnesium Silicate or Magnesium Aluminum Silicate CAS Number 12511-31-8 or 1327-43-1 or 12199-37-0 Specifications of Aluminium Magnesium Silicate BP Ph Eur Grade CAS 12511-31-8 Action and use: Excipient. DEFINITION Mixture of particles with colloidal particle size of montmorillonite and saponite, free from grit and non-swellable ore. Content: aluminium (Al; Ar 26.98): 95.0 per cent to 105.0 per cent of the value stated on the label. magnesium (Mg; Ar 24.30): 95.0 per cent to 105.0 per cent of the value stated on the label. CHARACTERS Appearance: Almost white powder, granules or plates. Solubility: Practically insoluble in water and in organic solvents. It swells in water to produce a colloidal dispersion. IDENTIFICATION A. Fuse 1 g with 2 g of anhydrous sodium carbonate. Warm the residue with water and filter. Acidify the filtrate with hydrochloric acid and evaporate to dryness on a water-bath. 0.25 g of the residue gives the reaction of silicates. B. Dissolve the remainder of the residue obtained in identification test A in a mixture of 5 mL of dilute hydrochloric acid and 10 mL of water. Filter and add ammonium chloride buffer solution pH 10.0. A white, gelatinous precipitate is formed. Centrifuge and keep the supernatant for identification C. Dissolve the remaining precipitate in dilute hydrochloric acid. The solution gives the reaction f aluminium. C. The supernatant liquid obtained after centrifugation in identification test B gives the reaction of magnesium. TESTS pH: 9.0 to 10.0. Arsenic: Maximum 3 ppm. Lead: Maximum 15 ppm. Loss on drying: Maximum 8.0 per cent, determined on 1.000 g by drying in an oven at 105C. Microbial contamination: TAMC: acceptance criterion 1000 CFU/g. TYMC: acceptance criterion 100 CFU/g. Absence of Escherichia coli. Specifications of Magnesium Aluminum Silicate USP NF Grade Magnesium Aluminum Silicate is a blend of colloidal montmorillonite and saponite that has been processed to remove grit and non-swellable ore components. The requirements for viscosity and ratio of aluminum content to magnesium content differ for the several types of Magnesium Aluminum Silicate, as set forth in the accompanying table. Type Viscosity(cps) (Al content)/(Mg content)   Min. ---- Max. Min. ---- Max. IA 0225 ---- 0600 0.5 ------ 1.2 IB 0150 ---- 0450 0.5 ------ 1.2 IC 0800 ---- 2200 0.5 ------ 1.2 IIA 0100 ---- 0300 1.4 ------ 2.8 Identification: Add 2 g in small portions to 100 mL of water, with intense agitation. Allow to stand for 12 hours to ensure complete hydration. Place 2 mL of the resulting mixture on a suitable glass slide, and allow to air-dry at room temperature to produce an oriented film. Place the slide in a vacuum desiccator over a free surface of ethylene glycol. Evacuate the desiccator, and close the stopcock so that the ethylene glycol saturates the desiccator chamber. Allow to stand for 12 hours. Record the Xray diffraction pattern, and calculate the d values: the largest peak corresponds to a d value between 15.0 and 17.2 angstrom units. Prepare a random powder specimen of Magnesium Aluminum Silicate, record the X-ray diffraction pattern, and determine the d values in the region between 1.48 and 1.54 angstrom units: peaks are found between 1.492 and 1.504 angstrom units and between 1.510 and 1.540 angstrom units. Viscosity: After determining the Loss on drying, weigh a quantity of Magnesium Aluminum Silicate test specimen equivalent to 25.0 g on the dried basis. Over a period of a few seconds, transfer the un-dried test specimen to a suitable 1-L blender jar containing an amount of water, maintained at a temperature of 25 ± 2 , that is sufficient to produce a mixture weighing 500 g. Blend for 3 minutes, accurately timed, at 14,000 to 15,000 rpm (high speed). [NOTE—Heat generated during blending causes a temperature rise to above 30 .] Transfer the contents of the blender to a 600-mL beaker, allow to stand for 5 minutes, and adjust, if necessary, to a temperature of 33 ± 3 . Using a suitable rotational viscosimeter equipped with a spindle as specified below, operate the viscosimeter at 60 rpm for 6 minutes, accurately timed, and record the scale reading. For Type IA, use a spindle having a cylinder 1.87 cm in diameter and 0.69 cm high attached to a shaft 0.32 cm in diameter, the distance from the top of the cylinder to the lower tip of the shaft being 2.54 cm, and the immersion depth being 5.00 cm (No. 2 spindle); if the scale reading is greater than 90% of full-scale, repeat the measurement, using a spindle similar to the No. 2 spindle but having the cylinder 1.27 cm in diameter and 0.16 cm high instead (No. 3 spindle). For Type IC, use a No. 3 spindle; if the scale reading is greater than 90% of full-scale, repeat the measurement using a spindle consisting of a cylindrical shaft 0.32 cm in diameter and having an immersion depth of 4.05 cm (No. 4 spindle). For Types IB and IIA, use a No. 2 spindle. Microbial limits: Its total aerobic microbial count does not exceed 1000 cfu per g, and it meets the requirements of the test for absence of Escherichia coli. pH: between 9.0 and 10.0, in a suspension (5 in 100) in water. Loss on drying: Dry it at 110C to constant weight: it loses not more than 8.0% of its weight. Acid demand: After determining the Loss on drying, weigh a quantity of Magnesium Aluminum Silicate equivalent to 5.00 g, and disperse in 500 mL of water with the aid of a suitable blender fitted with a 1-liter jar. Using a stopwatch, designate zero time. With constant mixing, add 3.0-mL portions of 0.100 N hydrochloric acid at 5, 65, 125, 185, 245, 305, 365, 425, 485, 545, 605, 665, and 725 seconds, and add a 1.0-mL portion at 785 seconds. Determine the pH potentiometrically at 840 seconds: the pH is not more than 4.0. Arsenic: The limit is 3 ppm. Lead: To pass the test The absorbance of the Test preparation is not greater than that of the Standard preparation (0.0015%). SDS MSDS of Aluminium Magnesium Silicate or Magnesium Aluminum Silicate BP Ph Eur EP JP USP NF IP ACS Analytical Reagent FCC Food grade Manufacturers

Crystal Clear Products and the group companies are manufacturing chemicals since several decades. We have automatic vacuum operated titanium evaporators and SS316 equipments to produce top grade of chemical products. We have toll manufacturers and representatives in China, UAE, Europe, Canada & USA and agents & customers in all countries like USA, Canada, Europe, UAE, South Africa, Tanzania, Kenya, Egypt, Nigeria, Uganda, Turkey, Mexico, Brazil, Chile, Argentina, Bangkok Thailand, Kaula Lumpur Malaysia, Dubai UAE etc. & sales representative in Chicago, Houston New York & Los Angeles, USA. Associated units are FDA-GMP certified, Halal and/or Kosher certified, REACH registered, ISO-9001, ISO-22000 HACCP certified, Crisil Rated.

Contact Aluminium Magnesium Silicate or Magnesium Aluminum Silicate IP BP Ph Eur EP JP USP NF ACS Analytical Reagent FCC Food Grade manufacturers exporters at:

Crystal Clear Products
Plot No-C1-1031-9, GIDC Estate, Panoli, Ankleshwar, Gujarat - 393002. India
Telephone Mobile: 91-7506449333; e-mail: info@crystalclearproducts.org

e-mail: info@crystalclearproducts.org

Manufacturers, Suppliers of IP BP Ph Eur EP JP USP NF FCC Food, ACS Reagent GMP Grades of Chemicals like Aluminium Magnesium Silicate or Magnesium Aluminum Silicate